Pettit Hydrocoat Ablative Antifouling Paint
Pettit Hydrocoat Ablative Antifouling Paint, Pettit Hydrocoat Waterbased Bottom PaintPettit Hydrocoat is an eco-friendly water-based marine bottom paint that meets all local and state regulations. It is formulated with no harsh smells or solvents. The Pettit Hydrocoat Bottom Paint is the industry leader in water-based ablative antifouling paints. It is formulated to be self-polishing and no pre-sanding is required. Pettit Hydrocoat helps protect bottoms from frequent cleaning, bleaching, trailering, and launching that can wear down boat finishes.Pettit Hydrocoat Bottom Paint comes in blue and black color options and is sold by the gallon. Its water-based formula makes it easy to apply with a brush or roller, and clean-up is easy with just soap and water. Use on aluminum hulls or outdrives is not recommended.Key Features: Self-polishing; 40% Cuprous Oxide; Copolymer Ablative technology; PTFE for slick fast finish; Multi-season Ablative; Minimal Odor, Easy Clean-up with Water; Environmentally friendly; Comparable to Interlux Micron CSC, and Pettit Horizons; Specifications: Type: Water-based ablative; Recommended Usage: All fouling waters; Colors Available: 1240 Blue, 1840 Black; Drying Time: To overcoat 3hrs; To launch; 6hrs. @ 70F; Number of Coats Recommended: 2-3; Coverage: 490 ft2/gal; VOC: 150 grams/liter; Biocide: Cuprous Oxide 40.43%; Associated Products:Pettit Protect Epoxy Primer - Primer for bare fiberglass applicationsPettit 120 Thinner - For surface prepHow To Apply Pettit Hydrocoat Bottom PaintHydrocoat is easily applied using a brush, roller or sprayer. For rollers, use a high-quality short nap (maximum 3/16" nap) roller cover. Apply using thin coats, as over-application will cause surface imperfections and shorter wear. Before applying, mix paint thoroughly. Clean and properly prepare surfaces prior to painting. TIP: For the smoothest possible finish: thin the paint 5-10% with clean fresh water. Wet the surface with fresh water. This will provide a truer color and smoother finish. Application Methods: Brush, Roller, Airless or Conventional Spray.; Number of Coats: 2 minimum with additional coat at waterline recommended.; Dry Film Thickness: 1.5 mils (3.75 wet mils); Coverage: 430 sq. ft/gal.; Application Temp: 50F Min. / 90F Max.; Thinner: Clean, fresh water; DRY TIMES: Temp To Touch To Recoat To Launch 90F 1/4 HR 1-1/2 HR 6 HR 70F 1/2 HR 3 HR 10 HR 50F 1 HR 6 HR 16 HR*The above dry times are minimums. Hydrocoat may be recoated after the minimum time shown. There is no maximum dry time before launching.Application Systems Previously Painted Surfaces; If the previous coating is in good condition, thoroughly sand with 80-grit sandpaper then solvent clean with Pettit 120 Thinner to remove residue. ; Apply two finish coats of Hydrocoat.; If the previous coating is soft or in poor condition, remove to the bare surface by sanding or using paint remover.; Proceed with appropriate bare system as described below.; Old tin or copper copolymers or Teflon-based antifoulings should be sanded thoroughly with 80-grit sandpaper to remove the chalky outer surface.; Wipe clean of sanding residue, then over-coat directly with Hydrocoat.; Bare Fiberglass; All fiberglass, regardless of age, should be thoroughly cleaned with Pettit 92 Bio-Blue Hull Surface Prep or de-waxed several times with Pettit D95 Dewaxer. Proceed with either sanding method or non-sanding method:; Sanding Method:; After the surface has been dewaxed, sand thoroughly with 80-grit paper to a dull, frosty finish.; Rewash the surface with Pettit 120 Thinner to remove residue.; Apply two coats of Pettit Hydrocoat.; Non-Sanding Method:; Thoroughly clean, de-wax and etch the surface with Pettit 92 Bio-Blue Hull Surface Prep using a medium Scotch-Brite pad in a swirling motion.; Rinse all residue from the surface and let dry. Make sure the entire surface has a dull, frosty finish.; Wipe surface to remove any excess moisture.; Apply two thin coats of Hydrocoat.; Barrier Coats; To render the bottom as water impermeable as possible, prepare the fiberglass surface as mentioned above (sanding method).; Apply two or three coats of Pettit Protect High Built Epoxy Primer per label directions.; Apply two thin coats of Hydrocoat,; Bare Wood; Bare wooden hulls should be sanded thoroughly with 80-grit sandpaper.; Wipe clean of sanding residue with Pettit 120 Thinner.; A coat of Pettit 6627 Tie-Coat Primer thinned 25% with Pettit 97 Epoxy Thinner should be applied directly to the bare wood.; Allow to dry for four hours.; Apply two thin coats of Hydrocoat.; Previously Painted Wood; Thoroughly sand with 80-grit sandpaper.; If priming is necessary on bare wood spots, apply a touch-up coat of Pettit 6627 Tie-Coat Primer thinned 25% with Pettit Epoxy Thinner.; Apply two thin coats of Hydrocoat.; Application Tips Hydrocoat does not require sanding between coats.; Slight variations in color and surface texture are not uncommon and will not affect performance.; When spraying, do not thin Hydrocoat more than 10% or inadequate paint film thickness will occur.; Burnishing the surface to create a slicker finish should be done with 400-600 grit wet-or-dry sandpaper after the coating has dried for seven days.; Do not use this product on aluminum hulls and outdrives.; Click to Download Pettit Hydrocoat Bottom Paint Application Instructions