Interlux Micron Extra w/ Biolux Antifouling Paint
Interlux Micron Extra w/ Biolux Antifouling Paint, Interlux Micron Extra w/ Biolux Ablative Antifouling PaintInterlux is known for its high-quality antifouling paints made with superior products and developed for long-lasting results in all types of waters. Interlux Micron Extra is a multi-season bottom paint that allows for repeated hauling, launching and relaunching of your boat with no need to repaint. Made with Biolux technology, which helps control slime and algae build-up. Its controlled polish finish helps prevent paint build up and gets smoother over time helping to increase fuel efficiency and overall performance of the vessel.Interlux Micron Extra is suitable for all types of boats. It can be applied to fiberglass, wood, and properly-primed metal but is not recommended for aluminum boat bottoms. It is available in seven popular colors. Two to three coats are recommended for complete coverage. When applied Interlux Micron Extra antifouling paint dries with a matte finish.Features: Suitable for use on all boats in every water condition; Antifouling paint offers protection year-round; Biolux technology blocks slime and increases antifouling performance; Allows boats to be hauled and relaunched without repainting; For use on fiberglass, wood, and properly-primed metal. NOTE: Do not use on aluminum.; VOC: 330 gms/ltr as supplied; Available Colors: 5690 Blue, 5691 Green, 5692 Red, 5693 Black, 5694 Shark White, 5695 Brown, 5696 Dark BlueAssociated Products: Special Thinner 216 - For wiping down previously painted surfaces and thinning; Fiberglass Solvent Wash 202 - To clean bare fiberglass prior to application; InterProtect - Epoxy barrier for blister protection, prevention, and priming; How to Apply Interlux Micron Extra Ablative Antifouling PaintSand surface and apply Interlux Micron Extra with Biolux over hard antifouling paint. Soft antifouling paints must be removed or overcoated with Primocon prior to an application of Micron Extra. Micron Extra with Biolux should be thinned only as needed and not exceed 10% per volume. Apply Micron Extra in temperatures above 50F. Should hull or air temperature fall below 50F during the 16 hour dry-time, extend dry-time to 36 hours minimum. Application Method: Brush, roller, or spray; Coats Required: Two coats minimum; Theoretical Coverage: 440 ft2/gal; Thinner (Brushing): Brush-Ease 433; Thinner (Spraying): Special Thinner 216; Dry Times Temp Touch Dry Immersion 50F 3 hrs 16 hrs 75F 2 hrs 16 hrs 95F 1 hr 16 hrs Surface PreparationPreviously Painted Surfaces In Good Condition: Remove loose paint by sanding with 80 grade paper. Remove sanding residue.; In Poor Condition: Remove antifouling paint in poor condition with Interstrip Semi-Paste 299E.; Bare Fiberglass It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using soap and water to remove loose dirt and contamination.; Flush with fresh water to remove the soap residue and allow to dry.; Remove mold release wax using one of the following Interlux products: Fiberglass Surface Prep or Fiberglass Solvent Wash 202.; Fill any surface imperfections with Interlux Watertite following the label instructions.; After the surface has been properly cleaned, follow one of the application systems below.; Fiberglass No Sand System Clean the surface following the preparation procedure above.; Apply one coat of InterProtect 2000E or Fiberglass No-Sand Primer following the label instructions for applying the primer and overcoating with antifouling paint.; Fiberglass Sanding System Clean the surface following the preparation procedure above.; Sand entire surface well with 80 grade paper until flat matte finish is obtained.; Remove sanding residue.; Blister Prevention System Apply the InterProtect system for the prevention of blisters.; Bare Wood Sand with 80 grade paper.; Apply first coat reduced 10% with Special Thinner 216.; Fill seams, if necessary, with Seam Compound Brown 30.; Application Apply at least 2 coats; Apply an extra stripe coat in areas of high wear such as chines, rudders, sterngear and any leading edges; Click to Download Interlux Micron Extra with Biolux Application Instructions