Interlux Micron CSC Antifouling Bottom Paint
Interlux Micron CSC Antifouling Bottom Paint, Interlux Micron CSC Ablative Bottom PaintInterlux is the industry leader in ablative bottom paints and it is trusted by boat owners for their long-lasting quality products. Interlux Micron CSC is a multi-season ablative paint developed with an innovative copper-copolymer formula that provides a controlled release of the antifouling biocide. This means when the boat is out of the water for extended periods, the paint will not lose its effectiveness It also allows the boat to be trailered and relaunched the following season without needing to be repainted. For added protection, try Interlux antifouling bottom paint.Protection against all types of fouling is easy with Interlux Micron CSC. It's made with the proprietary Micron Technology, which provides long-lasting protection against all the harsh elements. Recommended for powerboats and sailboats, Micron CSC helps reduce the build-up of old paint coats and minimize sanding. Algae, barnacles, weeds, and other fouling have no chance with this ablative bottom paint. Micron CSC protects below the waterline in all types of waters. Safe to use on wood, fiberglass, and properly primed metal boat bottoms and parts. Not recommended for aluminum hulls and fittings.Interlux Micron CSC is similar to Interlux's Micron Extra but is harder and wears away at a slower rate. Micron CSC has a higher solids content for added protection. Just as with many of the other paints in the Interlux line, it has a controlled polishing, which reduces build-up and reduces the need for sanding, saving you time and allowing for more time out on the water.Features: Matte finish; Haul and Relaunch without painting; Self Polishing - No Build up; Fast Drying Formula; Reduced Solvents Emissions Formula; High Film Build for added Protection and Longevity; Suitable for use below the waterline; Recommended Usage: All fouling waters; Trailerables, dry-stored, fiberglass, wood and steel hulls; Biocide: 37.2% Cuprous oxide; Drying Time: To overcoat: 16 hrs., To launch: 16 hrs. @73F; Pack Size: 1 US Quart, 1 US Gallon, 3 US Gallon(Blue, Green, Red & Black Only, US Only)Colors Available: Y5580-Blue, Y5581-Green, Y5582-Red, Y5583-Black, Y5584-Shark WhiteHow To Apply Micron CSC Antifouling Boat Paint Application Method: Airless Spray, Brush, Conventional Spray, Roller; Number of Coats: 2-3 minimum; Dry Film Thickness per Coat: 2 mils (3.4 wet mils); Coverage: 439.7 sq. ft/gal.; Application Temp: 50 F. Min. / 90F. Max.; Thinner: Special Thinner 216 or Brush-Ease 433.; For optimal results, a minimum of two coats of Micron CSC must be applied. Apply an extra stripe coat in areas of high water such as chines, rudders, stern gear, and any leading edges. Airless spray pressure should be 170-204 bar/2500-3000 psi use tip size 0.53mm/21.DRY TIMES:TempTo TouchTo RecoatTo Launch90F1 HR16 HR16 HR70F4 HR16 HR16 HR50F4 HR16 HR16 HRSurface Preparation:Previously Painted Surfaces: In Good Condition Remove loose paint by sanding with 80 grade (grit) paper.; Remove sanding residue.; In Poor Condition Remove antifouling paint in poor condition with Interstrip Semi-Paste 299E.; Bare Fiberglass:It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using soap and water to remove loose dirt and contamination.; Flush with fresh water to remove the soap residue and allow to dry.; Remove mold release wax using one of the following Interlux products, Fiberglass Surface Prep YMA601V or Fiberglass Solvent Wash 202 following the product label instructions.; Fill any surface imperfections with Interlux Watertite following the label instructions.; After the surface has been properly cleaned, follow one of the application systems below. No Sand System; Clean the surface following the preparation procedure above.; Apply one coat of InterProtect 2000E or Fiberglass No-Sand Primer following the label instructions for applying the primer and overcoating with antifouling paint.; Apply at least two coats of Micron CSC* allowing appropriate drying times.; Sanding System; Clean the surface following the preparation procedure above.; Sand entire surface well with 80 grade (grit) paper until flat matte finish is obtained. Remove sanding residue.; Apply at least two coats of Micron CSC* allowing appropriate drying times.; Bare Wood: Sand with 80 grade (grit) paper.; Wipe with Brush-Ease 433.; Apply first coat reduced 10% with Special Thinner 216.; Fill seams, if necessary, with Seam Compound Brown 30.; Application Notes: Colors may fade or change color at the waterline; Shark White may turn green above the true waterline; Do not apply Micron CSC over aluminum; Do not pplay Micron CSC over tin-based copolymer antifouling paints; Micron CSC Application Data is from Interlux Akzol Nobel Click to Download Micron CSC Application Instructions